A dirty shark navigator lift away vacuum cleaner can easily lose suction, so try to clean it more often. But, do you know how to clean your Shark Vacuum Cleaner properly? If not yet, follow my guide below:

How Often Should You Clean Your Shark Vacuum Cleaner?

According to information in the owner’s manual, you should clean filters every three months. Although the HEPA filter can work for two years without any problem, it can have an adverse effect on a machine if you do not take care if it  properly.

In general, to keep your shark lift away vacuum cleaner in good condition for a long time, you should clean it around four times a year. Or you had better perform this task when seeing one of the signs as follows:

• Decreasing suction power
• Emitting uncomfortable smell
• Producing gasp-like sounds
• Leaving dirt behind

What You Will Need

• Water
• Soap
• Microfiber cloth
• Soft brush
• A pair of scissors
• A pair of gloves 
• Two cups of vinegar
• Three teaspoons of baking soda

Pro Tips

It’s better to clean your machine outside because dirt can stick to your furnishings, and perhaps turn your beautiful walls into dark colors. If possible, you should put a sheet or a similar covering underneath your model. Or you will have to clean a mess after finishing cleaning your shark navigator lift away upright vacuum.

Step-by-Step Guide

Unplug your Shark vacuum

You should unplug your vacuum cleaner because only turning it off is dangerous. You don’t know when the machine can accidentally switch on.

Empty the Dust Bin

After removing the canister, empty the dirt and dust inside if you forgot to do this thing from the last cleaning section.

Soak it in soapy water and wash it with a microfiber cloth.

Rinse the dust bin in cold water and air dry. Don’t reassemble until the canister is dry entirely. The air-drying process takes you around one day.

Reassembling wet parts can create a suitable environment for the growth and development of mold, causing respiratory problems and other allergic reactions.

Clean the Filters

• Where are the filters in the shark navigator lift away vacuum cleaner?

You will see them after removing the dust bin from the vacuuming component. 

In the event of foam filters, you should dunk them in soapy water and wash them thoroughly. You can’t obliterate stained marks, so just ensure to clean it.

Washing felt filters can damage them, so you just need to tap them to loosen dirt and dust gently.

In case you have to wash felt filters, I can provide you with a solution. But, I am not sure about the result.

Soak them in soapy water as you did with foam filters. Try to touch them as lightly and carefully as possible. Rinse the soap off the units and lay them flat to air-dry for one day. If they seem worn out after drying, it’s time to replace new ones.

For HEPA filters, clean them as you did with other filters, but this type of filter requires more time for drying.

• Clean the Brush Head

No matter how high-quality your rotating brush is, it will collect debris on it, such as strings, hair, and other dirt. The amount of debris accumulates more over time, so you need to clean this part in a timely manner.

To start with, remove the floor accessory from the handle first by pressing a button at the end to release the brush head.

You need the support of a pair of scissors or snip debris to cut and get rid of the tangled hair and strings. While doing, try not to damage the bristles.

For stubborn dirt, soak a soft brush in water and scrub it thoroughly. Like the other steps, this also requires you to air-dry the brush for at least one day.

Selected For You: Shark Navigator Lift-Away Vacuum Reviews - Shark Navigator Lift-Away Bagless Upright Vacuum

Clean the Hose

Check both ends of the hose carefully and remove blockages, if any. If you do not do this, it might obstruct your vacuum cleaner’s normal functioning. . 

How to Remove Blockages and Odors from the Hose

Simply hold the hose under a tap of running water.

Use your hand to close each end of the hose in turn, then remove the hose from the water tap and shake well for a few minutes.

Make a mixture of baking soda and vinegar and pour it into the hose. Do the same with the steps above. Flush out the mixture with warm and cold water. Now, the blockages and odors go away.

Let it dry completely and reattach it to the machine.

Washing the Motorized Floor Nozzle

Turn the motorized floor nozzle upside down, gently tap it to loosen dirt and dust, and then remove the remaining with an old toothbrush.

Reassemble the Vacuum

Removing parts is easy but putting them back together is a more challenging task. So, when removing, make sure to keep in mind how the parts fit.

Spread a Fresh Scent

Ground coffee beans or ground cinnamon can cover your shark navigator lift-away bagless upright vacuum with a fresh scent. In case you love an overpowering scent, you can use a strong smell that will leave both your house and your machine with a fresh odor.

It is pretty easy to clean a Shark vacuum cleaner because you just need to prepare some essential items and follow my step-by-step guide. You will take the machine apart, remove a blockage, if any, rinse with water, air dry, reassemble, and you are done.

In case your machine has a serious problem that you can’t rectify, refer to shark navigator lift away reviews and shark navigator lift-away vacuum reviews on this website to buy a new one.

TheKingLive is a trustworthy website to provide readers helpful information about Amazon products. We make sure that you can make the right decision on a good-quality model at a reasonable price no matter what you want to buy on Amazon. We write qualified reviews based on experiences, tests, and hours of researching.